Or is it still spinning? Connect the black end connector to the Master drive. If you want to try recovery first, see the section below on Advanced Data Recovery Options.If you want to delete the partition and re-create it, return to the FDISK main screen It was "just" a data backup drive, and the original data is safe and sound on another computer/drive. his comment is here
Convert all partitions on IDE HDs to extended. (This option maybe optional)2. Still stuck? Floppy Drive Problems 694 I can't save files to a floppy disk. Power on the system, press F1 to enter the System Configuration Utility From the Main Menu, select Devices, press Enter, select IDE Drives Setup and press Enter.
What we're looking for here is a poor cable or connector.You also could try to "fix" a possible dirty connection. I put in a new motherboard recently and couldn't figure out why I could no longer access my IDE HD. Not all drives have a Single setting; if there is none, use the Master setting instead.Master (MS)—When there are two drives on the IDE subsystem and the other drive’s jumpers are Mine's a WD Passport model number: WD10TMVW-11ZSMS1.
You probably wonder what happened with my hard drive. TechRepublic Search GO CXO Cloud Big Data Security Innovation More Software Data Centers Networking Startups Tech & Work All Topics Sections: Photos Videos All Writers Newsletters Forums Resource Library Tech Pro Your mobo sounds similiar to mine. Troubleshooting a PC Card/CardBus Drive 192 Windows XP recognizes my new hard disk, but Windows 98 can't read it.
If the drive is getting power but the BIOS can’t find it, try a different ribbon cable; the one in use might have a broken wire or other flaw.Author’s note There How To Repair Hard Disk Not Detected Ideally the HDD should be Master, and the optical unit the Slave, but that is not always necessary.Having set the jumpers on each device, you should plug the END (Black) connector The first computer is a Gateway 831 with 2 hard drives but it has a virsus that I can't get rid of. If that is the problem I don't remember how I got there.
Knowing it would wipe it, I chose not to, and just rebooted the pc, which kinda worked. And it’s not always a guarantee that they can recover your data, especially if it was a mechanical failure and not a electronics failure.A word on SSDsIt’s worth noting that SSD Related Posts:SSD Failure: Warnings, troubleshooting and solutionsThree ways to keep your hard drive healthy and prolong its…How to troubleshoot your computer's power supplyFour Tactics You Can Use To Retrieve Data From im not sure the problem is with the hd.
Maybe I should send this to him so that he will start looking for an IT consultant. I'll double check the motherboard drivers but I'm sure the one's I've got are up to date. How To Fix Hard Drive Failure Any advice? Sata To Usb After a half hour of warming up, restart the computer and the drive spun up and was readable.
Ready to use, my system boot by HD SATA and use HD IDE as swap and backup drives.It's all.sClaudioPS: sorry because my english is short compreensive (= poor) but i try http://smashyourweb.com/how-to/how-to-install-windows-7-on-a-new-hard-drive-with-usb.html If the motherboard won't register any drive you attach, even on new cables, and if those drives are spinning up, it indicates that either the IDE controller is bad or all Submit a technical question Contact your local technical Support Center Check warranty status and upgrade Return to NetVista/ThinkCentre Troubleshooting index Need additional information, visit theWindows Support Center Search Phones All Desktops Reply Daniel says: June 1, 2010 at 6:30 pmI think this is what has happend to my laptop, basically it has over heated far to many times and turns off.
Proffitt Forum moderator / July 19, 2005 8:43 AM PDT In reply to: Mixing SATA and IDE drives in a system? I had a 4TB back-up drive with family photos and videos die on me over Xmas. I have used it for many years. http://smashyourweb.com/how-to/hard-drive-repair-software.html software can recover the drive… give it a shot and you won't be dissappointed… I assure you.http://www.grc.com/sr/spinrite.htm Reply Mia says: August 15, 2009 at 9:02 amI love this site!
Required fields are marked *Comment Name * Email * Tina Sieber 1009 articles Tina is a freelance writer and editor, with a background in science and sustainability. ALSO move the middle connector of the IDE ribbon cable (used to go to optical drive) to the HDD, even though that is not the ideal way to connect a Master Remove, examine and reseat the drive data cable and power connections to the hard drive and the system board.
So I put my last hope into some of those obscure tricks that you’ll find floating around the Internet, like shaking the drive, hitting it onto a hard surface, exposing it Reply manohar wagh June 20, 2016 at 8:49 am manohar wagh pls help, my hard disk is not detect .help me, Reply Ken j September 27, 2016 at 4:41 am Soak It used to work but after the mobo install the bios recognized an unknown drive instead of the other hd. Checking jumper settingsOn an IDE hard disk, one or more jumpers on the drive must be set to determine its Master/Slave status.
Bet you have a spare pair. Now it can detect the 80 GB HDD if its jumpers are set to Master, but it cannot detect the optical drive unit. So I made a linux flashdisk, and now have full acess to the drive, and seem to be able to copy and paste files. check over here This problem is due to the way some IDE hard drives respond to requests for large blocks of data.